MULTIQUIP GAW-135H Spezifikationen PDF herunterladen (Seite 17)

GAW-135H DC WELDER/AC GENERATOR — OPERATION MANUAL — REV. #1 (06/23/04) — PAGE 17

Single Phase Load

Always be sure to check the nameplate on the generator

and equipment to insure the wattage, amperage and

frequency requirements are satisfactorily supplied by the

generator for operating the equipment.

Generally, the wattage listed on the nameplate of the

equipment is its rated output. Equipment may require 130—

150% more wattage than the rating on the nameplate, as

the wattage is influenced by the efficiency, power factor and

starting system of the equipment.

If wattage is not given on the equipment's

name plate, approximate wattage may be

determined by multiplying nameplate

voltage by the nameplate amperage.

WATTS = VOLTAGE x AMPERAGE

The power factor of this generator is 1.0 See Table 2 below

when connecting loads.

NOTE

GAW-135H — LOAD APPLICATION

To determine the running wattage for your load, multiply

the running wattage as indicated by steps 1, 2, and 3 below:

1. INCANDESCENT LOADS

Lights, heaters and similar appliances.

Total the running wattage and multiply by 1.

Example:

29 light bulbs @ 100W each = 2.9 KW

use a 3 KW generator.

2. SMALL MOTORS

Drills and other small power tools.

Total the running wattage and multiply by 2.

Example:

A 1 inch drill runs at 1 KW

use a 2 KW generator.

3. LARGE MOTORS

Submersible pumps, table saws etc.

Total the running wattage and multiply by 3.

Example:

A conveyor belt runs at 8 KW

use a 24 KW generator.

NOTE

When using a combination of dual

receptacles, total load

should not

exceed

the rated capacity of the

generator.

Extension Cables

When electric power is to be provided to various tools or

loads at some

distance

from the generator, extension cords

are normally used.

Cables should be sized to allow for

distance in length and amperage so that the voltage drop

between the generator and point of use (load) is held to

minimum

. Use the cable selection chart (Table 2 ) as a

guide for selecting proper cable size.

The idle control device is operated at a

minimum load capacity of 100W. If the

load capacity is less than 100W, place

the idle control switch in the OFF position.

NOTE

)noitarepOesahPelgniS,zH06(noitceleSelbaC.3elbaT

nitnerruC

serepmA

sttaWnIdaoLhtgneLelbaCelbawollAmumixaM

stloV021tAeriW01#eriW21#eriW41#eriW61#

5.2003.tf0001.tf0

06.tf573.tf052

5006.tf005.tf003.tf002.tf521

5.7009.tf053.tf002.tf521.tf001

010021.tf052.tf051.tf001

510081.tf051.tf001.tf56

020

042.tf521.tf57.tf05

.egatlovwolmorftlusernacegamadtnempiuqE:NOITUAC

daoLyBrotcaFrewoP.2elbaT

daoLfOepyTrotcaFrewoP

srotomnoitcudniesahp-elgniS57.0-4.0

tnecsednacni,sretaehcirtcelE

spmal

0.1

yrucem,spma

ltnecseroulF

spmal

9.0-4.0

,secivedcinortcelE

tnempiuqenoitacinummoc

0.1

slootrewopnommoC8.0

Motors and motor-driven equipment draw much greater

current for starting than during operation.

Always

use an

adequate size

extension cable

which can carry the

required load.

CAUTIONCAUTION

CAUTION

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 83 84

Kommentare zu diesen Handbüchern

Keine Kommentare

MULTIQUIP GAW-135H Spezifikationen Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Stromgeneratoren MULTIQUIP GAW-135H